Maximizing the efficiency of production processes

Free consultation: +38(067) 577 13 75

Inspection conveyors for sour cherries

For visual inspection of sour cherries, compare an air-blow conveyor for washed fruit, polyurethane and modular belt models and a two-level conveyor that turns the fruit during transfer.

Berry processing machinery

Planning an inspection station for sour cherries

Inspecting sour cherries after washing

The INSORTEX inspection conveyor has a modular belt, adjustable speed, air blow-off for surface water and transport wheels. The catalogue specifies a 4,000 mm drum-centre length and an operating height of 850 mm adjustable by ±50 mm. Measure the washer discharge height and decide where staff will remove damaged cherries.

Polyurethane and modular belt models

Both catalogue models have an 800 mm belt and adjustable speed up to 0.2 m/s. The polyurethane belt has a guide cord and scrapers on the inside. The plastic modular model has a removable chute with discharge gates. Compare how operators inspect and clean the belt and how each model controls fruit discharge.

When to consider a two-level inspection conveyor

Cherries can turn as they move between the two belts, giving operators a different view of each fruit. Specify the defects you want to inspect after the transfer. On a representative trial, check the fruit condition and how much of the surface operators can see at the required feed rate.

Place the inspection station before or after washing

Manual inspection before washing allows operators to remove obviously damaged fruit and large visible debris. An inspection station after washing can be used for a closer look at surface defects. Specify where the cherries are inspected, whether surface water reaches the belt and how an even layer of fruit will be maintained while incoming containers are changed.

Operator positions and reject discharge

Locate the operator positions and reject containers next to the selection zone. On a trial batch, check visibility across the belt and the time operators have between feeding and discharge. For a station after washing, also plan where surface water will drain around the operator positions.

Transfer cherries from inspection to the next operation

For handover to pitting equipment, packing or another operation, measure the next machine’s inlet and record its feeding requirements. Mark any accumulation points and specify how the flow will be diverted while containers are changed. If the cherries are washed upstream, allow for drainage at transfer points.

Information for specifying an inspection conveyor for sour cherries

  • Input condition, approximate fruit diameter and the defects that operators should remove.
  • Peak feed rate, the number of inspection positions and the reject route.
  • Feeding and discharge heights, available width and direction of travel.
  • Cleaning procedure, downstream feed requirements and container dimensions.

Comparing inspection conveyors for sour cherries

OperationCatalogue equipmentDetails to confirm
Inspect sour cherries after washingModular belt with air blow-off. Catalogue working height 850 ± 50 mm.
Use a belt with scrapers800 mm polyurethane belt with guide cord and scrapers.
Transfer to the next machine using a removable chute800 mm modular belt and gates to stop discharge at the chute.
Inspect the other side of the fruit after turnoverTransfer between two belts. Check the fall height and fruit condition in a trial.

Equipment selection questions

Which conveyor turns sour cherries for inspection?

The two-level inspection conveyor can turn cherries during transfer between belts. Use your sample to check defect visibility and the condition of the fruit after the transfer.

How wide are the catalogue inspection belts?

The polyurethane and modular belt models are listed with 800 mm belts. Check that this fits the operator reach, number of inspection positions and required selection rate.

What is needed to connect the conveyor to a pitter?

Provide the inlet height, dimensions and direction of travel, required feeding pattern and distance between machines. If the pitter takes fruit in batches, plan for pauses and possible accumulation.

Can the conveyor also be used for other fruit?

Compare the fruit dimensions, tolerance for transfers and cleaning requirements for each crop. Validate a feeding speed for each product on representative batches before planning line changeovers.

Discuss your berry processing requirements

Leave your name and phone number. If you have a specification, tell us the berry type, incoming condition, required throughput and the operation you want to carry out.

+38 (067) 577 13 75

Name and phone number are required.